A single Wi-Fi router is no match for a larger home. You’re bound to run into a dead zone sooner or later, and then all is lost — especially if you have kids. Luckily, there’s a way to skip all the drama, and all it takes is a secondary router.
A secondary router acts as an extender that takes your Wi-Fi signal and re-transmits it. That’s a fresh data stream right out of thin air. Here’s how to do it.
Do a 30/30/30 reset
Before we configure everything, let’s make sure your DD-WRT router is using the default settings. To do this, we do what is called a hard reset — or 30/30/30 reset — which removes all configurations from the NVRAM of your router. Here’s how it’s done.
Note: As the DD-WRT Wiki warns, there are situations in which you shouldn’t do a hard reset or 30/30/30 reset. Don’t perform them while the router is upgrading. Don’t do them for Linksys EA series routers (as doing so can brick them). And don’t do them for any ARM routers.
Step 1: With the router plugged into the power supply, hold the Reset button located on the bottom of the router for 30 seconds. Your router will reset, and this is normal. Keep holding the button.
Step 2: Now, keep holding the Reset button, and unplug the router. Wait for 30 seconds.
Step 3: Keep holding the Reset button, and plug the router in. Keep the Reset button pressed down for 30 seconds.
That’s right: You’re holding the button for 30 seconds with the router on, then 30 seconds with the router off, then 30 seconds with the router on again. When this is done, you’re ready to do some configuring.
Setting up DD-WRT as a wireless repeater
Keep in mind that some router models (especially older routers) do allow you to set up the router as a repeater natively, which means you don’t need to use DD-WRT. Fortunately, many of our steps below can be used with native settings that allow it, even if things look different: Linksys, for example, has a different interface, and the method that Netgear’s Nighthawks use is also a bit different, while the Asus mode differs as well. Look for these options before downloading DD-WRT just to make sure they aren’t available. This can save you some time. Otherwise, you can proceed full steam ahead with DD-WRT.
If the router is currently plugged into any network, unplug it — we don’t need any Ethernet cables for a repeater. Now connect to the router wirelessly. The default SSID will be “dd-wrt,” and you’ll need to set an admin username and password.
Step 1: First, head to the Wireless section and click the Basic Settings tab.
Step 2: Set Wireless Mode to Repeater.
Step 3: Set Wireless Network Mode to match your router. This might require some research on your part, though Mixed is fairly universal.
Step 4: Set the SSID to match your router. We chose Potcasting, because that’s the name of the router we’re hoping to repeat.
Step 5: Under Virtual Interfaces, click Add.
Step 6: Give the new virtual interface a unique SSID. We used Potcasting-Repeat, but you can use whatever name you like. Just don’t use the same name as your primary network.
Step 7: Hit Save, but do not hit Apply Settings just yet. You should wait until you’re completely finished.
Now let’s head to the Wireless Security section.
Step 1: Under the Physical Interface section, make sure the settings exactly match those of your primary router. For example, if your primary router uses WPA2 Personal with TKIP encryption, set things the same here, and enter your key as you would if you were connecting from a PC or phone.
Step 2: Next, under the Virtual Interfaces section, you’ll establish the settings you’ll use to connect to this router. It’s best to make these identical to the settings in the Physical Interface section.
Step 3: Hit Save, but hold off on Apply Settings.
Almost done! Now, head to the Security section, disable the SPI Firewall, and uncheck everything housed under Block WAN Requests. Then, hit Save.
Finally, head to Setup and select Basic Setup. Under Network Setup, change the Router IP to a different subnet than that of your primary router. For example, if your main router’s IP is 192.168.1.1, set the repeater’s IP to 192.168.2.1. Don’t change the other number sets (192, 168, etc.) in the address, just this one.
With all of this done, go back to every page you configured and make sure all of the settings are correct. When you’re sure everything is right, hit the Apply Settings button. Your router will restart, and eventually, you’ll see the SSID you chose earlier for your repeater. Connect to it, and verify that your internet is working by heading to the Digital Trends website (or any other). If it works, you now have a wireless repeater!
If you can’t get this working, review your settings, or find more information on the DD-WRT wiki.
When it comes to physically placing it in your home, the repeater depends on receiving a wireless signal from your primary router to do its job, so placing it in a dead zone likely won’t do you much good. Ideally, the repeater should be placed near the dead zone, but close enough to the router to still get a decent signal. Experiment with different locations until you’re happy with the coverage and speed.
Can you use a router app?
If you have a router that uses its own app for settings management, you might be able to use this app to set up a repeater as well, without downloading DD-WRT — but it isn’t very likely. Take a look at your router app and see if it offers a repeater mode or a setting that allows you to switch the router to an extender. If you find this option, remember to make your mobile device forget your router first so it doesn’t keep trying to connect it the old way.
However, this usually only works if your router app natively supports switching to a repeater. If it doesn’t, you’ll need to make the changes from DD-WRT on a desktop. Many router companies have phased out repeater modes, so they aren’t common on newer routers and their apps. That’s why we recommend DD-WRT. And some router setups, like Google WiFi’s mesh system, just aren’t compatible with extension modes at all because of the way they work.
Setting up DD-WRT as a second access point
Make sure that your router is not plugged into anything but the power. Connect wirelessly — the default SSID will be “dd-wrt,” and you’ll have to set an admin username and password.
You’ll start at the Basic Setup page. Some router settings will have an extra mode called AP Mode or Bridge Mode that is specifically for setting up a second access point. If you find this mode, you should certainly try to activate it: Your router may then pick up a lot of the information listed below automatically, saving you a lot of time. Just be careful you aren’t unintentionally activating a repeater mode instead: These router setting terms can be vague, so it’s always important to study the details of your own router settings page.
Here you need to:
Step 1: Change the local address to something other than what your primary router uses. We used 192.168.1.2. Take note of this IP, because you’ll need it later to configure your access point.
Step 2: Enter the IP address used by your primary router under Gateway. This is typically 192.168.1.1, but check to make sure.
Step 3: Disable the DHCP Server. This will prevent your access point from fighting your router to assign IPs.
Step 4: Assign the WAN port to switch. This isn’t necessary, but it gives you an extra port later if you need it.
Step 5: Hit Save, but don’t click Apply. Your router isn’t ready, and it will misbehave if you apply the new settings too early.
Next, head to the Wireless section, and make the following changes on the Basic Settings sub-page.
Step 1: Make sure Wireless Mode is set to AP. It should be the default.
Step 2: Choose an SSID. This can be the same as your primary router if you’d like, but if so, ensure that this access point and the router are using different channels. For example, if your primary router is set to Channel 1, set this one to Channel 11 to avoid conflicts. If that’s too complicated, just use two different SSIDs.
Step 3: Hit Save, but not Apply.
Now, head to the Wireless Security subsection. If you left the SSID identical to that of your primary router, copy the security settings here. This will ensure that your devices seamlessly switch between the two access points. If you used a different SSID, feel free to use different security settings, but sticking to WPA2 is recommended if you want your network to be secure.
Next, head to the Security section, and disable the firewall. Because this router will not be filtering your connection to the internet, this is unnecessary at best and a source of problems at worst.
Review all of the above settings, and when you’re happy click, Apply Settings. Then, restart your router and connect it to the network somewhere near a dead zone.
The Access Point can be placed in the extreme corners of the dead zone, provided there is a wired connection available. This allows for better coverage where you need it most but depends on where you have wired access to the network.